Wheel alignment, sometimes referred to as breaking or tracking, is part of standard automobile maintenance that consists of adjusting the angles of the wheels so that they are set to the car maker’s specification. The purpose of these adjustments is to reduce tire wear, and to ensure that vehicle travel is straight and true (without “pulling” to one side). Alignment angles can also be altered beyond the maker’s specifications to obtain a specific handling characteristic. Motorsport and off-road applications may call for angles to be adjusted well beyond “normal” for a variety of reasons. NEC AIR COMPRESSORS AND PUMPS
All new vehicles leave the factory with their alignment checked and adjusted. Usually the technician paints the heads of the adjustment hardware to show it has been set, also to show if it has moved later on. It is advisable to do the alignment of the car after the first 5000 km, since all the suspension get set. Failure to do this may result in the camber and toe specifications drifting outside the manufacturer’s limit. This may lead to vehicle pulling and tire wear.
Initially consumers may not notice these defects but after usage of some days or running some kilometers it can cause uneven tire wear and a pull/drifting to the left or right. Tire wear leads to frequent replacement of tires thus adding to running cost for the consumer.Vehicle pulling causes irritation and/or fatigue while driving the car. NEC AIR COMPRESSORS AND PUMPS
Under normal driving conditions many vehicles can go 50 000 km+ before they need a new set of tires, which is a good interval to have the alignment checked as well. Any severe driving incidents, or changed suspension components would also warrant a check.
The typical alignment on an economy sedan takes about an hour under ideal circumstances. A utility or performance vehicle may require additional labor. When fasteners and hardware are rusted/seized, extra time may be required and/or parts may need to be replaced. A good start is to consult your local licensed automotive technician.
In the same fashion that you will wear out your shoes if you walk only on the inside or outside edge, so your tires may become worn if not within allowed specifications. Many performance vehicles sacrifice tire life for driving performance.
As the tire will bounce, it is the first spring that your car rides on, affecting and potentially shortening the life of all other components. Braking distance, ride quality, and even fuel economy are all affected by the correct inflation and rotation of tires. A major improvement in fuel savings would result if everyone correctly inflated their tires. NEC AIR COMPRESSORS AND PUMPS
If your vehicle squeals while turning corners on dry pavement, it is probably time to have your alignment checked. (or slow down)
Changing rims and tires will normally not affect the alignment but will affect secondary angles. Consult your local licensed automotive technician.
The primary angles are the basic angle alignment of the wheels relative to each other and to the car body. These adjustments are the camber, caster and toe. On some cars, not all of these can be adjusted on every wheel.
These three parameters can be further categorized into front and rear (with no caster on the rear, typically not being steered wheels) so summarily the parameters are:
- Front: Caster (left & right)
- Front: Camber (left & right)
- Front: Toe (left, right & total)
- Rear: Camber (left & right)
- Rear: Toe (left, right & total)
The secondary angles include numerous other adjustments, such as:
- SAI (Steering Axis Inclination) (left & right)
- Included angle (left & right)
- Toe out on turns (left & right)
- Maximum Turns (left & right)
- Toe curve change (left & right)
- Track width difference
- Wheelbase difference
- Front ride height (left & right)
- Rear ride height (left & right)
- Frame angle
- Setback (front & rear)
Setback is the difference between right side and left side wheelbase length. It can also be measured as an angle. Setback less than the manufacturer specified tolerance (for example about 6mm) does not effect car handling. That’s because, when the vehicle is turning, one wheel is ahead of the other by several centimetres and therefore the setback is negligible. There are even some car models with different factory setting for right and left side wheelbase length, for various design reasons. An off-spec setback may occur because of a collision or a difference between right and left caster.